Page 4 of 4 FirstFirst 1234
Results 31 to 36 of 36

Thread: Trying to go wireless

  1. #31
    Old Man Winter member Ruppro's Avatar
    Join Date
    Jan 2016
    Location
    Lizella GA
    Posts
    1,033
    No Bill did put out a V2.0 and, it not in that thread but, I remember you finding a bug that he fixed w/ the 2.1 dev version. now that my mind has stopped hurting

    and w/ the v2.1 the blue light should be on solid on the ESP
    Matt

    Briar Creek Lights
    2017 My 2nd Year
    2016 150 Renard channels (and a few pixels,110)
    Honorary DIGWDF engineer

  2. #32
    Senior Elf member
    Join Date
    Jan 2015
    Posts
    151
    Quote Originally Posted by mrGrumpy View Post
    Break the connection between the bottom right pin and the wire solder point. Scrap with razor blade or x-acto knife

    Light on ESP should be on, and I remember seeing something lit below the snap-in. Red
    That was it. Itís working now. Going to test all the rest of the Channels later tonight.
    Thank you to everyone that gave some input. I would be lost without yall help.




    Sent from my iPhone using Tapatalk

  3. #33
    Old Man Winter member Ruppro's Avatar
    Join Date
    Jan 2016
    Location
    Lizella GA
    Posts
    1,033
    Quote Originally Posted by louisiana-lights View Post
    That was it. It’s working now. Going to test all the rest of the Channels later tonight.
    Thank you to everyone that gave some input. I would be lost without yall help.
    Glad to see you got it working.

    and as far a Vixen, yes you make one e1.31 controller for all 328 channels and then each ESP is set to its start channel and the # of channels on the controller like MrGrumpy showed back in the beginning

    Quote Originally Posted by mrGrumpy View Post
    Use full universe only - 510 or 512 - match Vixen and ESP (boundary).
    OK to only use 328 channels of universe.

    I used 512, and pulled 10 ESP's off universe 1
    First ESP - start 1, boundary 512, channel count 8
    2nd ESP - start 9, boundary 512, channel count 16
    3rd ESP - start 25, boundary 512, channel count 24
    and so on for 10 ESP's
    Matt

    Briar Creek Lights
    2017 My 2nd Year
    2016 150 Renard channels (and a few pixels,110)
    Honorary DIGWDF engineer

  4. #34
    Senior Elf member
    Join Date
    Jan 2015
    Posts
    151
    Quote Originally Posted by Ruppro View Post
    Glad to see you got it working.

    and as far a Vixen, yes you make one e1.31 controller for all 328 channels and then each ESP is set to its start channel and the # of channels on the controller like MrGrumpy showed back in the beginning
    Thatís how I have it one controller with all the channels. Iím glad I only built that one board. Will be a lot easier to cut the path before I assemble the boards.



    Sent from my iPhone using Tapatalk

  5. #35
    DIGWDF Engineer member dirknerkle's Avatar
    Join Date
    Nov 2011
    Location
    Plymouth, MN USA
    Posts
    10,052
    Quote Originally Posted by louisiana-lights View Post
    Thatís how I have it one controller with all the channels. Iím glad I only built that one board. Will be a lot easier to cut the path before I assemble the boards.



    Sent from my iPhone using Tapatalk

    Good job. The board was originally designed for Bill Porter's firmware, which uses the TX output pin on the ESP. Shelby's firmware uses the GPIO2 pin instead. You can't have both connected at the same time. Breaking the connection eliminates the TX pin signal.
    Even though the DIGWDF Store has closed, it's still awesome! Thanks to all who have supported us through nearly 7 years of excitement!
    Parts of the store will remain open for downloading documentation, firmware and Gerber/DipTrace files: http://digwdf.org/store


  6. #36
    Santa's Helpers Falcon's Avatar
    Join Date
    Nov 2011
    Location
    Salem, Orygun Just South of Canby
    Posts
    2,224
    Success. Yippie

Page 4 of 4 FirstFirst 1234

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •